Infinibowl

Let the bowl keep singing

Infinibowl holds the note for as long as you need, so your hands are free to hold the room.

Sound on. The tone is synthesised in your browser.

Someone always has to stay on the bowl

A rimmed singing bowl only sings while a hand keeps circling it. So whoever holds the space spends the session with one arm locked to a stick, when they want to be guiding a breath, adjusting a pose, tending a fire or playing a second instrument.

Infinibowl takes over the circling. You choose the bowl, set how fast and how firmly, and it holds that note steadily for an hour or for a whole night.

Yoga studios

A drone under savasana while the teacher walks the room and gives adjustments.

Sound baths

One bowl holds the ground note while you play gongs, chimes and other bowls over it.

Ceremonies

A continuous tone through an opening, a long meditation or a vigil, with nobody tied to it.

Frequency events

Several Infinibowls on one stage hold a chord. Each holds its pitch, and they start and stop together.

How a bowl sings, and how Infinibowl keeps it singing

When you rim a bowl, the wand doesn’t slide smoothly. It grips the metal, drags it a fraction of a millimetre, lets go, and grips again, hundreds of times a second. Each release lands in time with the bowl’s own ring and adds a little energy, the way small pushes keep a swing going. Physicists call this stick-slip. A bowed violin string works the same way.

It works because friction gets weaker as the sliding gets faster. When the rim swings away from the wand, the grip eases off. When it swings back, the grip tightens. Over each cycle the wand gives the bowl more energy than it takes away.

The note comes from the bowl flexing into a slight oval that pulses in and out. The point where the wand touches becomes a node: the place where the rim slides sideways the most and moves in and out the least.

By hand, the stick travels round the bowl and drags the oval with it. You hear the note pulse four times for every circuit.
Suede on bronze, design values. Infinibowl works on the falling part of this curve.

Turn the bowl, not the stick

To rim a bowl, the stick and the rim have to slide past each other. A hand moves the stick round a still bowl. Infinibowl does the opposite: it turns the bowl on a heavy platter and holds the wand still. Physically the friction is the same. The difference is where the oval points. With a fixed wand the oval stays put, so the note is a steady drone without the slow “wah-wah” of a travelling stick. For a room full of people lying still, most practitioners prefer it.

Three things set the sound, and Infinibowl controls all three:

  • Rim speed, 0.05 to 0.6 m/s. Slower is darker and needs more pressure. Faster brings out the upper partials.
  • Contact force, 1 to 8 N, about the weight of a small apple to a bag of sugar. Too little and the bowl never catches. Too much and it chatters.
  • Contact height, 10 mm below the rim, where the rim flexes most for the least effort.

Try it: stick-slip, simulated

This is a live model of the rim under the wand: one mass on a spring, driven by the friction curve above. Find the band where the bowl sings cleanly.

Four ways to keep a bowl singing

We drew up four mechanisms and scored each against what matters in a quiet room full of people. Sound counts three times. The turntable won because it does nearly everything well and nothing badly.

Weighted scores, out of 5 for each criterion

Infinibowl IB-1

Drag to turn it. Pull it apart to see the drive, choose a bowl or take it away, and click any part to see what it’s made of.

Bowl

Click a part on the model to see what it is, what it’s made of and how it’s made.

Inside Infinibowl

Four parts work together: a drive that turns the bowl, a head that holds the wand, a base that keeps everything still, and a small computer that listens.

The drive

We borrowed the drive from a record player, because record players solved quiet, even rotation decades ago. A pancake stepper turns a 12 : 1 rubber belt, and the belt turns a crowned pulley under an 820 g aluminium platter. The belt soaks up the motor’s tiny step-by-step jerks. The heavy platter smooths out the rest, including the push and pull of stick-slip at the rim.

Platter speed
3 to 115 rpm
Drive ratio
12 : 1, flat belt
Bearings
2 × 6001-2RS, 24 mm apart
Speed feedback
4096 counts per turn

The head

The wand is real hard maple in a suede sleeve, hung from a pivot so it can swing toward the rim. A soft spring inside the arm pulls on a cord tied to the top of the wand. The pivot doubles the leverage, so the rim feels half the cord tension. A micro linear stepper in the pod at the back stretches the spring to set the force. Because the spring is soft, a bowl that wobbles half a millimetre changes the force by less than one per cent. That steadiness is what stops rattling.

The head slides up the mast for taller bowls and along the arm for wider ones. Two brass thumbscrews lock it. With no power the cord goes slack and the wand swings 5 mm clear of the rim, so it can never be left pressing on the bowl.

Contact force
1 to 8 N, set in 0.1 N steps
Spring
0.3 N/mm, stainless
Lever
2 : 1 (70 mm below pivot, 35 above)
Bowls
Ø100 to 300 mm, 45 to 130 tall

The base

A 3 mm laser-cut steel plate gives Infinibowl 1.4 kg of low, flat weight. The printed shell sits over it. All the working forces are internal, because the wand pushes on the bowl and the bowl pushes back through the same frame. So weight isn’t needed to hold anything in place. It’s there so a knocked elbow or a dog’s tail doesn’t move the machine. Sorbothane feet stop the floor hearing the motor, and stop footsteps reaching the bowl.

Footprint
358 × 230 mm
Height
330 mm to the mast cap
Mass
3.8 kg without a bowl
Power
USB-C, under 8 W

The ear

A microphone in the tower listens to the bowl 16,000 times a second. Infinibowl finds the bowl’s pitch, watches how strongly it rings, and listens for the harsh buzz of chatter. If the note drifts or starts to rattle, it adjusts speed and force by small amounts. It learns each bowl in a 40-second sweep and remembers it.

The numbers behind it

Every figure on this page comes from one specification file, the same one that builds the 3D model and the drawings. Move the sliders to see what the machine has to do for your bowl.

Design values. Friction is suede on bronze, μ 0.4 sliding and 0.6 at grip. We’ll confirm them on the prototype.

Drawings

Five A3 sheets in third-angle projection, generated from the same specification as the model. Open any sheet to read it full size, or download the SVG to print or import into CAD.

Electronics and firmware

Every part is an off-the-shelf module on one small carrier board, joined by keyed connectors. There’s no soldering in the kit and no mains voltage anywhere in the machine.

Power

A 20 W USB-C charger feeds the board. A PD trigger chip asks it for 12 V for the motors, and a small buck converter makes 5 V for the processor and display. In normal running Infinibowl draws under 5 W, about the same as a phone charging.

The parts that think

  • ESP32-S3: runs the control loop, the pitch tracking and the radio.
  • 2 × TMC2209: drive the two steppers so quietly you hear the bowl, not the motor.
  • AS5600: a magnet under the spindle tells it the platter angle.
  • INMP441: the microphone in the tower.
  • Round display and dial: turn to set, press to start or stop.

A session, start to finish

  1. Idle. The wand hangs clear and the platter is still.
  2. Engage. The platter comes up to speed, then the actuator draws the wand onto the rim over two seconds.
  3. Bloom. Force starts at 1.5 × the set value so the bowl catches quickly, then eases back as the note grows.
  4. Sustain. The microphone holds the level you set. If it hears chatter, it slows the platter 5 % and adds 0.2 N, the same fix a player makes by hand.
  5. Release. The wand lifts clear smoothly, never snapping away.
  6. Ring-out. The platter coasts to a stop while the bowl rings on by itself.

Several Infinibowls in one room talk over ESP-NOW, a direct radio link with no Wi-Fi network needed. One leads and the rest follow, so a chord starts and ends together.

What’s printed, and what isn’t

About a third of the parts are 3D printed, but not the ones that matter most for sound. Anything that needs mass, a true axis or a natural material is machined, cut or bought. Totals are at one-off prices.

Build manual

Thirteen steps, about three hours with the tools listed. Every connector is keyed and every fastener is metric. If your kit came assembled, skip to step 13.

Time
3 h
Tools
Hex keys 1.5 to 3 mm, soft-jaw vice, scissors
Skill
Flat-pack furniture, plus pressing in two bearings

Set-up, use and care

Fitting a new bowl

  1. Drop in the seat ring that matches the bowl’s foot. The chart is inside the lid.
  2. Loosen the height thumbscrew and slide the head until the line on the wand is 10 mm below the rim.
  3. Clip the 5 mm gauge on the rim and bring the arm in until the wand touches it. Lock it and remove the gauge.
  4. Hold the dial for two seconds. Infinibowl runs its 40-second sweep and saves the bowl.

In a session

Press the dial to start. The note blooms in about ten seconds. Turn the dial to make it louder or softer. Press again and the wand lifts away while the bowl rings out. On the app you can set a timer, a slow fade, or a chord across several Infinibowls.

Water in the bowl works. It lowers the pitch and makes the water dance. Keep it below a third of the bowl’s depth, and Infinibowl will re-tune itself.

Care

  • Turn the suede sleeve a quarter turn every 20 hours. Replace it at about 200 hours. A spare comes in the box.
  • If the note gets grainy, rub the sleeve gently with a soft brass brush.
  • The belt lasts about 3,000 hours. It is a standard turntable belt.
  • Wipe the bowl rim with a dry cloth. Oils from hands reduce grip.

Safety

  • 12 V low voltage only. The charger is UKCA and CE marked.
  • The platter turns at walking pace at most, about 0.6 m/s at the rim. A hand on the bowl stops it, and Infinibowl stops the motor.
  • Keep loose hair, scarves and mala beads away from the turning bowl.
  • Don’t leave it running unattended overnight with candles nearby.
  • Hearing: a large bowl can reach 90 dB close up. Set a lower level for long sessions.

Making it at scale

The first hundred are hand-assembled and tested from printed parts. Each change after that brings the unit cost down without changing how it sounds.

QuantityHow it’s madeParts cost
1 to 100Printed shell and brackets, CNC platter, laser-cut plate. Assembled and tuned by hand in the UK.About £187
100 to 1,000Platter turned in batches. Carrier board with every module soldered on. Shell printed on a print farm.About £130
1,000 and upShell, tower and pod injection-moulded in glass-filled PP. Platter die-cast and turned. About £18,000 in tooling.About £85

How we’ll test it

  1. Friction rig. Measure μ for suede, felt and leather on bronze across 0.05 to 0.6 m/s, to replace the design values with real ones.
  2. Bowl library. Sing 30 bowls from Ø100 to 300 mm and record the force and speed window where each one sings cleanly.
  3. Self-noise. With no bowl fitted, Infinibowl must be quieter than 25 dB(A) at 1 m.
  4. Endurance. 500 hours of continuous singing on three machines. Check sleeve wear, belt stretch and bearing noise.
  5. Safety and EMC. UKCA and CE testing before the first sale.

Bring an Infinibowl into your space

We’re building the first run now. Tell us how you’d use it and we’ll write when the prototypes are ready to try.

This opens your email app with a message to hello@max-os.xyz. Nothing is sent until you press send.

Download SVG